-
Posted by
steve21 July 23, 2009 -
1,023 views
Several years ago I was reading a article by author Chuck Hawks about the .308 Norma Magnum great article for anyone fascinated with military history and the many firearms that have been used or developed due to information provided by history. After spending several hours at the shooting range one Saturday morning I decided to go home and research more, after a career around the development and testing of firearms for the service, this so called .308 mag had my interest. With the knowledge and history behind the .308 caliber and its many years of purpose I wanted to play, so like a little kid I started to dig out several old Russian Mosin Nagants that I had stored away in the junk boxes ( parts ).These guns have been around for decades and can be bought at local surplus store for 50 - 100 dollars depending on condition. Now anyone that knows about the history of the model 1891/30 will be quick to tell you they are a military tank that you shoot from the upright position ( un - destructible ). The most of the mass production line was made in the 7.62 x 54 mm ( .308 cal. military version ) with a barrel that seem to reach the next country they where very accurate and maintenance free, if dropped you could simply pull the trigger drop the bolt wash off, re-insert and you where up and running again.With a rear adjustable trajectory sight ( 1000 yrds ) these were by far one of the very best production service riffles every made.I have never been afraid to work with any of these old service riffles as unlike todays versions the metal and craftsmanship is second to none. Any how I sat down and re - read the article again and come to the conclusion that I could simply take a Model 1891 / 30 and rebuild it into a .30 - 338, this is not a simple task without the proper machining tools.First and foremost the biggest problem with any of the old Nagants - Mousers is the bolt when in open position does not give you much room to mount any type of optical other than a couple of side mount versions ! ( what ) a re - constructed play toy with a side mount - definitely not taking that to shooting range.So to start my project I ordered a full length synthetic stock piece that would need to be hand crafted to fit this new sniper version.Stream line is the word - next was to re -cut the bolt configeration as to allow for a shallow retraction lane - not that simple as I now have to work the bolt as it will be retracting a .338 Winchester Mag casing.This is when machining is a must - I have to stuff a .338 magnum into a breach that was mad to hold a 7.62 x 54 casing.However cutting the story short - it takes several hours of very precision machining to re - work this area of the firearm, making a mistake means throwing away a perfectly good piece of history.I cut the barrel to a exactly 28 inc. machine treaded the end for a 6 inc. machined break choke - this will help with the noise level more so than the ugly shoulder breaking punch. ( keep in mind i am dropping approx. 4.5 pounds off this factory creature )next task was to cut outside diameter of the barrel down prior to fitting it with new stock.I started and ended up cutting from 1/8 th in at front of barrel to almost 1/4 in at rear of barrel - wow ! what a change in weight.Now that the barrel was turned down I drilled tapped and fitted scope rings, it seem that I was going to have approximately 3/4 in of clearance between the bolt slide and the bottom of the scope - great ! just what the doctor ordered.Now a simple process that most do not try on there own and can save that favorite piece of history and or personal family heirloom.Do to the amount of guns I work on I have a electronic laser bluing tank, great for those 4 ft monsters ( muskets ).After bluing and cooling several times of all the pieces of my newly created monster, It was time for assembly.Plan B - building a re-load that would do what I was expecting to accomplish, off to the powder room I go - now I remember reading that I was going to be looking to establish a shot that would contain a maximum pressure of 55,100 psi that doesnt sound like much but its somewhere to start - remember I am going to shoot a fully customized gun that is 77 years old for the first time - better safe than sorry.My accomplishment was exactly a starter shell - using the Hodgdon Data Manual I started with statistics of a .308 magnum 79.5 grains of H1000 powder packed into my newly pressed .338 mag casing and topped with a perfectly pressed 150 grain bullet.Ok - the day has come, off to the range with my new piece that I was so proud of - like I said knowing the history behind this awesome looking riffle i was carrying it was a great feeling to show off and be proud of. Bore sited prior to going to the range, it was time to fine tune this weapon of mass destruction, I laid this unit out on the rest and without breathing I loaded one of these ( new ) projectiles into the chamber and closed up the bolt - not sure what to expect I still was not breathing at this time and was shaking - thank god for the rest caboooooooom ( son of bitch ) !What a sound ! I am sure everyone at the range took for cover, Now i have shot a lot of different weapons from a pellet gun up to the bad daddy of them all the Barret .50 cal.This was something I had never felt before - wow ! after all the excitement had passed I started to fine tune and very quickly discoverd that this new rocket launcher was just the beginning.After about 50 rounds I was tuned into a group 1/4 in grouping at 500 yards. Ok I am happy with that ( NOT ).Back home I started playing with loads and weights - today this unit is a conversation piece at any range with the older gentleman that know of this unit in its military form.Now this is a load that I am sharing with our readers however I will not take responsability if you use and fail to wake up after trying. I use Norma brass casing ( NEW ) - necked down to hold a .308 caliber bullet ( 150 grain InterLock - Hornady ) powered by 90.5 grains of RL - 25 powder.This giving me a 1000 yrd shot with a drop of 9.722 inches / muzzle velocity of 3,460 fps and very comfortable re-coil that lets me shoot 50 rounds plus with little to now suffering.This is my .30 - .338 cal Russian Mosin Nagant Model 1891 / 30 - cost ( PRICELESS )